Cisco 300-360 Exam With Updated Exam Questions – [Dec-2017 Dumps]

This Cisco Certified Network Professional Wireless 300-360 exam required skills and knowledge if you want to pass 300-360 exam. Designing Cisco Wireless Enterprise Networks 300-360 exam dumps is designed in a way that it cover all the key points of actual 300-360 exam. Braindumps4cisco provide you latest exam questions that realy provide you assistance in you actual Network Services 300-360 exam. There are four basic domains to be measured by this exam are Professional, and .

300-360 exam questions, 300-360 PDF dumps; 300-360 exam dumps:: https://www.dumpsschool.com/300-360-exam-dumps.html (83 Q&A) (New Questions Are 100% Available! Also Free Practice Test Software!)

Latest and Most Accurate Cisco 300-360 Dumps Exam Questions and Answers:

Version: 9.0
Question: 21

An engineer is preparing for an active site survey of a hospital and is informed that he or she should
not enter any active surgery suites. Which option describes how the engineer should address this
restriction?

A. Conduct a passive wireless survey in the restricted areas.
B. Use the predictive AP placement tool on the wireless controller.
C. Skip the area and estimate where to place the access points.
D. Arrange to perform survey activities after hours.

Answer: A

Explanation:
Passive surveys are surveys that are performed with a listen-only mode. The survey client never
associates to the access point (AP). Such surveys can be helpful when you look for rogue devices
or you want a good gauge of downlink RF coverage from the infrastructure devices.
These can be accomplished with a passive survey:
– Identify rogues
– Locate RF trouble zones quickly
– Validate final RF setting
– Perform initial surveys
The most significant loss of information with passive surveys is uplink information, Physical (PHY)
rate boundaries and retransmission. PHY rates are generally based on RF signal and noise levels.
A passive survey only reports signal propagation for beacons measured by particular clients. PHY
rates can only be measured by actual data that is sent to and from an AP.
https://www.cisco.com/c/en/us/support/docs/wireless/5500-series-wireless-controllers/116057-
site-survey-guidelines-wlan-00.html

Question: 22

An access point will be partially exposed to the outdoor environment in a loading dock of a factory.
How should this access point be deployed in a cost-effective manner?

A. indoor AP with an external leaky coaxial cable
B. outdoor mesh AP utilizing the 5-GHz band
C. outdoor bridge AP pointing its antenna toward the factory
D. indoor-based AP inside a NEMA-rated enclosure

Answer: B

Explanation:
Because mesh radio waves have very high frequency in the 5-GHz band, the radio wavelength is
small; therefore, the radio waves do not travel as far as radio waves on lower frequencies, given
the same amount of power. This higher frequency range makes the mesh ideal for unlicensed use
because the radio waves do not travel far unless a high-gain antenna is used to tightly focus the
radio waves in a given direction.
https://www.cisco.com/c/en/us/td/docs/wireless/technology/mesh/7-
0MR1/design/guide/MeshAP_70MR1.html#wp1849065

Question: 23

New Updated 300-360 Exam Questions 300-360 PDF dumps 300-360 practice exam dumps: https://www.dumpsschool.com/300-360-exam-dumps.html

An engineer is preparing for an indoor wireless LAN survey and is provisioning a survey kit. Which three pieces of equipment should be included? (Choose three.)

A. external connector access point
B. integrated antenna access point
C. coax low-loss cable
D. battery operated power supply
E. range finder
F. Yagi antennas

Answer: BDE

Question: 24

Which three options are benefits of U-APSD? (Choose three.)

A. optimized power-save mode periods
B. increased call capacity
C. bandwidth reservation
D. synchronization of the transmission and reception of voice frames
E. efficient roaming
F. priority bandwidth and polling

Answer: ABD

Explanation:
Unscheduled automatic power-save delivery (U-APSD) is a feature that has two key benefits:
The primary benefit of U-APSD is that it allows the voice client to synchronize the transmission and reception of voice frames with the AP, thereby allowing the client to go into power-save mode between the transmission/reception of each voice frame tuple. The WLAN client frame transmission in the access categories supporting U-APSD triggers the AP to send any data frames queued for that WLAN client in that AC. A U-APSD client remains listening to the AP until it receives a frame from the AP with an end-of-service period (EOSP) bit set. This tells the client that it can now go back into its power-save mode. This triggering mechanism is considered a more efficient use of client power than the regular listening for beacons method, at a period controlled by the delivery traffic indication map (DTIM) interval, because the latency and jitter requirements of voice are such that a WVoIP client would either not be in power-save mode during a call, resulting in reduced talk times, or would use a short DTIM interval, resulting in reduced standby times. The use of U-APSD allows the use of long DTIM intervals to maximize standby time without sacrificing call quality. The U-APSD feature can be applied individually across access categories, allowing U-APSD can be applied to the voice ACs in the AP, but the other ACs still use the standard power save feature.
The secondary benefit of this feature is increased call capacity. The coupling of transmission buffered data frames from the AP with the triggering data frame from the WLAN client allows the frames from the AP to be sent without the accompanying interframe spacing and random backoff, thereby reducing the contention experience by call.
Reference: http://www.cisco.com/c/en/us/td/docs/solutions/Enterprise/Mobility/vowlan/41dg/vowlan41dg-book/ vowlan_ch2.html#wp1045982

Question: 25

A customer has restricted the AP and antenna combinations for a design to be limited to one model integrated antenna AP for carpeted spaces and one model external antenna AP, with high gain antennas for industrial, maintenance, or storage areas. When moving between a carpeted area to an industrial area, the engineer forgets to change survey devices and surveys several APs. Which option is the best to reduce the negative impact of the design?

A. Deploy the specified access points per area type.
B. Resurvey and adjust the design.
C. Increase the Tx power on incorrectly surveyed access points.
D. Deploy unsurveyed access points to the design.

Answer: B

Question: 26

An engineer is performing a predictive wireless design for a carpeted office space, which requires voice capability and location services. Which two requirements are inputs to the design? (Choose two.)

A. overlapping -67 dBm coverage from three access points
B. overlapping -75 dBm coverage from three access points
C. overlapping-72 dBm coverage from two access points
D. continuous -67 dBm coverage from one access pointE. continuous -72 dBm coverage from one access point

Answer: BD

http://www.cisco.com/c/en/us/td/docs/solutions/Enterprise/Mobility/emob73dg/emob73/ ch3_WLAN.html#pgfId-1000250

         

Facebook Comments