Cisco 642-883 Exam With Updated Exam Questions – [Jan-2018 Dumps]

This Cisco Certified Network Professional Service Provider 642-883 exam required skills and knowledge if you want to pass 642-883 exam. Deploying Cisco Service Provider Network Routing 642-883 exam dumps is designed in a way that it covers all the key points of the actual 642-883 exam. Braindumps4cisco provide you latest exam questions that really provide you assistance in you actual Routing and Switching Services 642-883 exam. There are four basic domains to be measured by this exam are Professional, and.

♥♥ 2018 NEW RECOMMEND 642-883 Exam Questions ♥♥

642-883 exam questions, 642-883 PDF dumps; 642-883 exam dumps:: https://www.dumpsschool.com/642-883-exam-dumps.html (130 Q&A) (New Questions Are 100% Available! Also Free Practice Test Software!)

Latest and Most Accurate Cisco 642-883 Dumps Exam Questions and Answers:

Question: 21

Refer to the exhibit.

R1 and XR2 cannot establish OSPF adjacency. Which option is the root cause of this issue?

A. stub flag mismatch
B. mismatched passwords
C. process ID mismatch
D. mismatched authentication types
E. MTU mismatch

Answer: D

Question: 22

A network engineer wants to test a path between any two points in the network for multicast traffic to identify congestion points in the network. Which command in a Cisco IOS XE router shows multicast traffic drops?

A. mstat
B. mtrace
C. mrinfo
D. ping

Answer: A

Question: 23

On Cisco IOS XR Software, which set of commands is used to enable the gi0/0/0/1 interface for OSPF in area 0?

A. interface gi0/0/0/0
ip address 10.1.1.1 255.255.255.0
!
router ospf 1
network 10.1.1.1 0.0.0.0 area 0
B. interface gi0/0/0/0
ip address 10.1.1.1 255.255.255.0
!
router ospf 1
network 10.1.1.1 255.255.255.255 area 0
C. router ospf 1
area 0
interface GigabitEthernet0/0/0/1
D. interface gi0/0/0/0
ip address 10.1.1.1 255.255.255.0
ip ospf 1 area 0
E. router ospf 1
address-family ipv4 unicast
interface GigabitEthernet0/0/0/1 area 0
F. router ospf 1
address-family ipv4 unicast
interface GigabitEthernet0/0/0/1
area 0

Answer: C

Question: 24

Which three statements are true regarding the OSPF router ID? (Choose three.)

A. The OSPF routing process chooses a router ID for itself when it starts up.
B. The router-id command is the preferred procedure to set the router ID.
C. If a loopback interface is configured, its address will always be preferred as the router ID over any other methods.
D. After the router ID is set, it does not change, even if the interface that the router is using for the router ID goes down. The router ID changes only if the router reloads or if the OSPF routing process restarts.
E. In OSPF version 3, the OSPF router ID uses a 128-bit number.

Answer: A, B, D

Question: 25

Which two OSPF network scenarios require OSPF virtual link configuration? (Choose two.)

A. to connect an OSPF non-backbone area to area 0 through another non-backbone area
B. to connect an NSSA area to an external routing domain
C. to connect two parts of a partitioned backbone area through a non-backbone area
D. to enable route leaking from Level 2 into Level 1
E. to enable route leaking from Level 1 into Level 2
F. to enable OSPF traffic engineering

Answer: A, C

Question: 26

What is function of the RP/0/RSP0/CPU0:PE1(config-ospf)#distance Cisco IOS-XR command?

A. To modify the administrative distance of the OSPF routes
B. To modify the default seed metric of the OSPF external routes
C. To modify the OSPF default reference bandwidth
D. To modify the OSPF cost

Answer: A

Explanation:
http://www.cisco.com/en/US/docs/ios_xr_sw/iosxr_r3.8/routing/command/reference/rr38ospf.pdf

New Updated 642-883 Exam Questions 642-883 PDF dumps 642-883 practice exam dumps: https://www.dumpsschool.com/642-883-exam-dumps.html